Philips Universal Remote PM3 User Manual

PM3  
Front Cover Art  
 
Setup  
Setup, cont.  
Battery Installation  
TV Volume/Mute Punch-Through Feature  
1. On the back of the remote,  
push down on the tab and  
lift the cover off.  
2. Match the batteries to the  
+ and - marks inside the  
battery case, then insert 2  
AAA Alkaline batteries.  
3. Press the battery cover  
back into place.  
The TV Volume/Mute punch-through feature lets you  
control the Volume and Mute function of your TV in any  
mode programmed to be a VCR, DVD, CABLE or SAT  
device, without needing to change to TV mode.  
VCR/DVD Punch-Through Feature  
Punch-through to VCR/DVD mode i.e. the 6 keys (PLAY,  
PAUSE, STOP, FF, REWIND, andREC) is only allowed  
in modes programmed for TV or Cable codes.  
Battery Saver  
Your remote automatically  
turns off if the buttons are  
depressed more than 30  
seconds. This will save your  
batteries should your remote  
get stuck in a place where the  
buttons remain depressed  
(e.g., between the sofa  
cushions).  
Code Setup  
The CODE SEARCH button is used to setup the remote.  
You can either setup the remote using the code for your  
brand of product, from the code tables (on separate  
sheet), or you can search through the library of codes  
until you find a code that works for your product.  
Please refer to “Programming with Code Search” on page  
11 for more information on using the code search feature  
to learn how to search through the library of codes for  
your products.  
Code Saver  
NOTE: You can store any kind of code under any mode  
(except TV). I.E. you can store a VCR code under the  
CBL button, or a DVD code under the VCR button, etc.  
However, you can only store TV codes under the TV  
button.  
You will have up to 10 minutes to change the batteries  
in your remote without losing codes you have  
programmed. However, do not press any buttons until  
batteries are installed in the remote. If buttons are  
pressed without batteries in the remote, all codes will be  
lost.  
PO WE R  
VCR  
D VD  
TV  
CBL  
Power-On Default  
QUIT  
The remote powers on in TV mode.  
OK  
INFO  
MENU  
SELECT  
IN/OUT  
C ODE  
S EAR CH  
S UB  
P R EV.  
C HAN  
S LEE P  
TITLE  
CODE SEARCH  
R EP EAT  
4
5
 
Button Functions  
Button Functions, cont.  
Some buttons on the remote might have functions that  
are referred to by different names on the device you are  
controlling. E.G. PREV.CHAN may be called RECALL, or  
ENTER may be called DISPLAY. These differences depend  
on the brand and model of your product. Also, this  
remote can only operate features that exist on your  
product. E.G., your product must have PREV.CHAN  
ability for the PREV.CHAN button to operate this feature.  
CHANNELUP/  
DOWNChanges  
the channels.  
POWER  
VOLUMEUP/  
DOWNChanges  
the volume level  
of the product,  
normally the TV.  
QUITexits  
Turns  
from Menu  
mode.  
product On  
or Off.  
MENUIN/OUT  
Toggles in and out  
of menu mode.  
Accesses the Menu  
functions of the  
device you are  
PO WE R  
CBL  
MUTETurns off  
the TV sound  
while the picture  
remains. Use for  
OK/SELECTin  
Menu mode.  
TV, VCR/DVD, Indicator light  
CBLSelects  
product to be  
operated.  
Lights when any  
button is pressed.  
VCR  
D VD  
TV  
QUIT  
controlling.  
OK  
PREV.CHAN Returns  
to the previously  
PO WE R  
CHAPTER+/-  
controls DVD track  
selection i.e. DVD  
Track Skip Up/Down  
(in DVD mode). Note  
the DVD Transport  
keys also control DVD  
when in DVD Mode.  
VCR  
selected channel, or  
DVD repeat toggle.  
REPEAT performs DVD  
players “A-B Repeat”  
(or RPT A.B) function  
for repeat play of  
INFO  
MENU  
D VD  
CBL  
SELECT  
IN/OUT  
TV  
QUIT  
C ODE  
S EAR CH  
S UB  
TITLE  
P R EV.  
C HAN  
S LE EP  
OK  
R EP EAT  
current Chapter or  
Track.  
INFO  
MENU  
SELECT  
IN/OUT  
INFO/SELECT  
displays/selects  
on-screen channel  
information, etc.  
C ODE  
S UB  
P R EV.  
C HAN  
CC(SUBTITLE)  
TV Closed  
Caption (if your  
TV has this  
feature) or DVD  
Subtitle toggle.  
S LE EP  
S EAR CH  
TITLE  
INPUT  
TV/  
VCR  
R EP EAT  
ENT  
SLEEPTurns off the  
TV after a period of 1  
to 99 minutes.  
S CAN R EW  
REC  
PLAY  
S CAN FF  
PAUS E  
STOP  
CODE SEARCH For setup.  
INPUT  
TV/VCR/INPUT  
For some TVs, press  
repeatedly to select  
from available  
TV/  
VCR  
ENT  
NUMBERS  
Enter numbers for  
direct channel  
S CAN R EW  
REC  
PLAY  
S CAN FF  
PAUS E  
STOP  
viewing sources  
(TV, CBL, etc.).  
selection. Some  
products require Enter  
to be pressed after  
channel selection.  
RECORD, PLAY, STOP,  
REW, FF, PAUSEVCR  
control buttons operate  
your VCR even when the  
remote is set to operate  
the TV. Also operates  
DVD Scan -/+.  
Note: The REC button must  
be pressed TWICE to record  
from your VCR. For some  
brands of VCRs, you might  
need to press the REC  
ENTER  
Used after direct  
channel number  
entry to immediately  
change to the  
button once, then press it  
again for three seconds.  
selected channel.  
6
7
 
Advanced Button Functions  
Advanced Functions, cont.  
DVD Functions  
VCR/DVD Punch-Through Feature  
SCAN+ and SCAN- buttons control the speed of Fast  
Forward and Reverse Playback respectively.  
CHAPTER+ andCHAPTER-buttons respectively  
locate the succeeding or preceding Chapters or Tracks  
on a disc.  
SUBTITLE button turns the subtitles on or off.  
REPEAT button performs DVD players “A-B Repeat” (or  
RPT A.B) function for repeat play of current Chapter or  
Track.  
INFO/SELECTbutton brings up DVD Display or  
Control Menu for Chapter/Track/Title number, Time  
remaining/elapsed indication, system information, etc.  
QUIT button is used to Exit or Clear on-screen Menu  
displays.  
PLAY button is used to start Disc playback and for  
Menu selection on some DVD players.  
STOP button stops Disc playback.  
This remote lets you Punch-through to the last VCR or  
DVD device used. Normally other types of remotes only  
punch-through (from another Mode) on the 6 VCR  
buttons, to the device programmed under the VCR  
Mode button. This is not much use if you are using a  
DVD programmed under a Mode other than VCR. This  
remote punches-through to the last VCR or DVD device  
you used. For example, if you have 3 DVD/VCR devices  
programmed into this remote, the last one you accessed  
on the remote will be the one that has control of the 6  
VCR/DVD buttons when in any other mode.  
TV/VCR/INPUT  
When in TV mode theTV/VCR/INPUTbutton performs  
the INPUT source switch function.  
When in a mode that has been programmed for VCR the  
TV/VCR/INPUT button performs the TV/VCR antenna  
switch function.  
When in a mode that has been programmed for Cable the  
TV/VCR/INPUT button performs the A.B switch  
function.  
When in a mode that has been programmed for SAT the  
TV/VCR/INPUT button performs the TV/SAT switch  
function.  
When in a mode that has been programmed for DVD the  
TV/VCR/INPUT button performs the DVD Setup  
function.  
PAUSE button pauses Disc playback - press PLAY to  
resume.  
INPUTbutton activates the DVD Player’s SETUP Menu.  
MENUIN/OUT  
The Menu In/Out button allows you to toggle in and out  
of Menu Mode. Pressing Menu In/Out brings up your  
device Menu. While in Menu mode the remote’s red  
indicator light blinks continuously. The remote will exit  
Menu Mode after 20 seconds if no keys are pressed.  
While Menu Mode is active, the Menu, Channel,  
Volume, Mute and Mode keys perform the following  
functions:  
TV/VCR and TV/DVD Combo units  
Note that for some TV/VCR and TV/DVD combo units  
you might need to set up two different buttons to  
control both parts of the combo unit. E.G., (referring to  
the Direct Code Entry section on the following page)  
you might need to set up a code under the TV button to  
control the TV part of the combo unit AND a separate  
code for the VCR or DVD under any other button you  
choose.  
MENU IN/OUT Exits/Enters Menu mode.  
CHANNEL UP/DOWN Up/Down commands for on-  
screen Menu navigation.  
VOLUME UP/DOWN Right/Left commands for on-  
screen Menu navigation.  
MUTE OKcommand for on-screen Menu selection.  
TV Mode Key Quit, Exit or Clear command to quit on-  
screen Menu and return the remote to normal operation  
(red indicator is now off). Note this action is also  
available by pressing any Mode key.  
Misc.  
OK means same as SELECT - some manufacturers use  
OK label and others use SELECT label on their remotes.  
CC will activate the Closed Caption feature if your  
device has that feature.  
8
9
 
Code Entry  
Code Entry, cont.  
Direct Code Entry  
Programming with Code Search  
1. Press and hold the CODE SEARCH button until the  
red indicator stays on, then release the CODE  
SEARCH button.  
2. Press and release the desired mode button (TV, VCR,  
etc.). The red indicator blinks, then stays lit.  
3. Enter the 3 digit code from the code tables (on  
separate sheet). Note: after a valid code entry, the  
red indicator turns off. For an invalid code, the red  
indicator flashes.  
4. With your device on, press CHANNEL UP. If the  
device responds, no further programming is  
required. Note: If some buttons do not operate your  
equipment, try one of the other codes for your  
brand.  
If your product does not respond after you have tried all  
the codes for your brand, or if your brand is not listed,  
try searching for your code by following these steps.  
1. Manually turn on the device (TV, VCR, etc.) to be  
controlled.  
2. Press and hold the CODE SEARCH button until the  
red indicator stays on, then release the CODE  
SEARCH button.  
3. Press and quickly release the desired mode button  
(TV, VCR, etc.). The red indicator blinks off once.  
4. Press the CHANNEL UP button repeatedly (up to 300  
times) until the device to be controlled changes  
channel. The red indicator blinks off with each  
button press. If you accidentally overshoot the  
code required, press the CHANNEL DOWN button  
to backtrack through the library until the device  
changes channel. Pressing CHANNEL UP changes  
direction to forward again.  
PO WE R  
VCR  
D VD  
TV  
CBL  
2.  
5. Press and release MUTE to install the code.  
QUIT  
Most users will store VCR codes under the VCR button,  
Satellite codes underSAT , etc. If (for example) you want  
to store a VCR code under SAT, first follow the procedure  
for Direct Code Entry (page 10) and press SAT in step 2  
of Direct Code Entry, then enter ANY VCR code in step 3  
of Direct Code Entry. Then follow the steps above for  
Code Search (or Brand Search, page 12).  
OK  
INFO  
MENU  
SELECT  
IN/OUT  
C ODE  
S EAR CH  
S UB  
P R EV.  
C HAN  
S LEE P  
TITLE  
1.  
3.  
R EP EAT  
Note: If the device does not have a CHANNEL UP  
button, use PLAY (VCR only) or POWER instead. Code  
Search starts from the currently stored three digit  
number under that mode.  
Write your codes down here for easy reference later.  
VCR  
D VD  
TV  
CBL  
3.  
Type  
TV  
Type stored  
TV  
Code  
QUIT  
4.  
5.  
OK  
VCR  
DVD  
Cable  
INFO  
MENU  
SELECT  
IN/OUT  
C ODE  
S EAR CH  
S UB  
P R EV.  
C HAN  
S LE EP  
TITLE  
2.  
R EP EAT  
10  
11  
 
Code Entry, cont.  
Code Entry, cont.  
Code Search by Brand  
Brand Search Table  
Look up your brand in the appropriate column (TV, VCR,  
etc.). Look to see what digit (1, 2, 3, etc.) applies to your  
brand, and enter it in step 4 of “Code Search by Brand”  
on the previous page.  
Lets you search for a code for a specific Brand within  
the Code Library for a particular manufacturer.  
1. Turn on the device (TV, VCR, etc.) to be controlled.  
2. Press and hold the CODE SEARCH button until the  
red indicator remains on, then release CODE  
SEARCH button.  
3. Press and quickly release the desired mode button  
(TV, VCR, etc.). The red indicator blinks off once.  
4. Press and release the numeric button (0-9)  
corresponding to desired Manufacturer (see table on  
next page). The red indicator blinks off once. Note,  
pressing “0” performs a full library search same as  
normal Code Search Method on previous page.  
5. Press the CHANNEL UP button ((or POWER or PLAY  
(VCR only)) repeatedly until the device to be  
controlled changes channel. The red indicator blinks  
off with each button press. If you accidentally  
overshoot the code required, press the CHANNEL  
DOWN button to backtrack through the library until  
the device changes channel. Pressing CHANNEL UP  
changes direction to forward again.  
6. Press and release MUTE to install the code.  
Brand Search Method entry is now complete.  
Note: When all codes under a Brand have been searched  
the red indicator flashes rapidly for 3 seconds.  
PO WE R  
VCR  
D VD  
TV  
CBL  
3.  
QUIT  
5.  
6.  
OK  
INFO  
MENU  
SELECT  
IN/OUT  
C ODE  
S EAR CH  
S UB  
P R EV.  
C HAN  
S LE EP  
TITLE  
2.  
4.  
R EP EAT  
12  
13  
 
Sleep Timer  
Code Identification  
The Sleep feature enables the remote to turn off the TV  
after a period of 1 to 99 minutes. Remote is to be in TV  
mode to set a Sleep Timer. This feature works even if  
your TV does not have this feature.  
Code Identification Feature  
The Code Identification Feature allows you to identify  
the three digit library code stored under your device key.  
For example, if you want to find out what three digit  
code is stored under your TV device key, follow the six  
steps below:  
1. Press and release the TV Mode button.  
2. Press and hold the SLEEP button until red indicator  
remains on (occurring after approx. 2-3 seconds).  
1. Press and hold the CODE SEARCH button until the  
red indicator stays on. Release the CODE SEARCH  
button.  
QUIT  
OK  
2. Press and release the desired mode button (TV,  
VCR, etc.). The red indicator blinks, then stays lit.  
3. Press and release the CODE SEARCH button. The  
red indicator blinks off.  
INFO  
MENU  
SELECT  
IN/OUT  
4. To find the first digit for the code stored under the  
mode key pressed in step 2, press each numeric key  
from 0-9 in turn. When the red indicator blinks off  
the number you pressed is the first digit for the code  
you are searching for.  
5. To find the second digit, repeat step 4, this time  
when the red indicator blinks off this is the second  
digit.  
C ODE  
S UB  
P R EV.  
C HAN  
S LE EP  
TITLE  
S EAR CH  
R EP EAT  
3. Release the SLEEP button.  
4. Press and release the numeric buttons (01-99) for the  
time required. The red indicator blinks off to indicate  
button press acceptance and remains off after the  
second button press.  
6. Repeat step 4 again to find the third digit.  
5. TV Sleep Timer now set.  
6. Leave the Remote pointing towards  
the TV with an unobstructed path.  
PO WE R  
VCR  
D VD  
TV  
CBL  
To cancel the Sleep Timer, press and hold the SLEEP key  
for 2-3 seconds until the red indicator blinks or press  
and release the POWER button in TV Mode.  
2.  
QUIT  
OK  
INFO  
MENU  
SELECT  
IN/OUT  
C ODE  
S EAR CH  
S UB  
P R EV.  
C HAN  
S LEE P  
TITLE  
1, 3.  
R EP EAT  
4.  
14  
15  
 
Product Operation  
Troubleshooting  
After the batteries are installed and you have  
programmed the remote for the codes that operate your  
products, you can use your remote to operate a TV, VCR,  
DVD, or Cable Box.  
Remote does not operate your product.  
Press the mode button of the product you want to  
control.  
Program the remote with a new code.  
Install new batteries. (You might have to reprogram  
your remote after installing new batteries.)  
Remote may not be compatible with your product.  
Remote does not operate some features of your product.  
Program remote with a new code.  
Remote may not be able to operate all features of  
your product or button names might be different  
than your product.  
Indicator light blinks after you program a product  
code.  
TV (PressTVFirst)  
Remote did not accept the code.  
Try to program the code again or try a different  
code.  
For help with setup, please call: 919-573-7854.  
VCR  
DVD Player  
(PressVCR/DVDfirst)  
(PressVCR/DVDfirst)  
Cable Box  
(PressCBLfirst)  
To Operate:  
1. Press theTV, VCR/DVD, or  
CBL button (depending on  
which product you want to  
operate).  
2. Aim the remote at the product.  
3. Press POWER to turn on the  
product.  
4. Press other buttons to operate  
the features of your product.  
16  
17  
 
Notes  
Notes  
18  
19  
 
90 Day Warranty  
This product is manufactured to PHILIPS MAGNAVOX  
specifications and is free from defects in material,  
workmanship and assembly. This warranty extends only  
to the original purchaser and is nontransferable. Should  
a defect occur under normal operating conditions within  
90 days from the date of purchase, PHILIPS  
MAGNAVOX will provide a comparable replacement free  
of charge within the warranty period, to the original  
purchaser. Defective product must be returned, with the  
dated proof of purchase, to the place of purchase for  
replacement. This warranty does not extend to the  
product if it has been damaged or rendered defective as  
a result of accident, misuse, abuse, tampering with or  
modification. THIS WARRANTY IS IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED,  
INCLUDING THE IMPLIED WARRANTIES OF MER-  
CHANTABILITY OR FITNESS FOR A PARTICULAR  
PURPOSE. IN NO EVENT SHALL PHILIPS  
MAGNAVOXBELIABLEFORSPECIAL, INDIRECT,  
INCIDENTAL OR CONSEQUENTIAL DAMAGES,  
WHETHERINCONTRACT,TORTORNEGLIGENCE.  
Some States do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not  
apply to you. Some States do not allow exclusion or  
limitation of incidental or consequential damages, so the  
above limitation or exclusion may not apply to you. This  
warranty gives you specific rights and you may also  
have other rights, which vary from State to State.  
Made in China-TC, Quality Assured in USA  
Clifton, NJ 07014-1115  
PM3 Back  
Cover Art  
 

Pelco Network Card C2907M D User Manual
Pentax Camcorder O FC1 User Manual
Petsafe Water Dispenser 400 1254 19 User Manual
Phoenix Gold Speaker ISM4 User Manual
Plantronics MP3 Player Accessories M12 User Manual
Powermatic Planer 201HH User Manual
Premier Mounts Indoor Furnishings PP FCMA User Manual
ProForm Treadmill 831291770 User Manual
ProForm Treadmill PFTL79103 User Manual
ProForm Treadmill PFTL999080 User Manual