AMX Universal Remote CC IRC User Manual

CC-IRC  
Infrared Emitter  
Download from Www.SomanuCalso.cnomt.rAoll MlaSnuyalsstSeeamrch AAndcDcoewnslosaod.ries  
CC-IRC IR Emitter Overview  
The IR Emitter adheres directly to the IR control window of your  
equipment by using clear two-sided tape to securely adhere the opaque  
shield. This “standard configuration” allows you to control your equipment  
either from either IR emitters or a hand-held remote control.  
The two black adhesive-backed window shields (Figure 3) are included  
within each emitter package and allow for alternate configurations. With  
this shield (surrounding the internal emitter), you can restrict IR reception  
through the device’s control window by blocking any interference or IR  
signals produced by sources other than the internal emitter. Without this  
shield, any incoming IR signal can pass through to the IR control window  
and overlap signals sent via the emitter (Figure 1).  
Note: Each CC-IRC package is shipped with four sealed alcohol pads  
which can be used to clean any adhesive residue left from a previous  
installation of the window shield on the surface of a device’s IR  
control window.  
 
Pass-Through Configurations  
This method allows IR signals generated from hand-held remotes to easily  
pass through the opaque red shell/cover. The internal IR LED can be  
oriented to either face towards or away from the shell (Figure 1),  
depending on its output configuration. Use the low-output configuration  
when device is being saturated by an IR signal. Use the high-output  
configuration when the device isn’t receiving enough of an IR signal and  
requires more strength. The side with the round “bump” is the high-output  
side.  
Low-Output  
High-Output  
Towards  
IR window  
Away from  
IR window  
Adhesive  
Download from Www.Somanuals.Fciogmu.rAell1Manuals Search And Download.  
Removing the Factory-Installed Shell  
The factory-installed shell  
is easily removed by  
carefully separating the  
two halves with a  
sharp-edged tool, such as  
an X-Acto™ knife.  
The IR LED can then be  
reversed or removed  
when the shell is  
Figure 2  
separated. Once the IR emitter and/or shield  
installations have been completed, the housing  
can be re-assembled by pressing the two halves  
firmly together.  
 
Shielded Configuration  
Use this configuration to prevent interference from fluorescent lights or  
other IR sources. The metallic shield prohibits passage of external IR  
signals and ensures proper IR signals will be received from the emitter.  
1. Remove the IR LED from the factory-installed shell (Figure 2).  
2. Test fit the location and size of the IR shield (Figure 3) on the target  
device. If necessary, use scissors to trim the shield to fit the opening  
of the IR window.  
3. Remove the adhesive backing from the IR shield and carefully place  
the IR LED into the recessed area using the correct orientation  
(Figure 1). Make sure the wires attached to the IR LED are not  
shorted together.  
4. Flip the shield-emitter combo back over and begin to carefully position  
the shield over the IR control window so that it covers the entire  
surface (Figure 4). This keeps any other signal from coming through.  
5. Press firmly on the shield surface to activate the pressure-sensitive  
adhesive.  
Opaque IR Window Shield  
Figure 3  
 
Cable Assembly  
IR Input Control Window (on device)  
IR Emitter Shield  
IR Emitter  
Controlled Equipment  
(DVD, CDP, VCR, etc.)  
Figure 4  
 
AMX Limited Warranty and Disclaimer  
AMX Corporation warrants its products to be free of defects in material and workmanship under  
normal use for three (3) years from the date of purchase from AMX Corporation, with the  
following exceptions:  
Electroluminescent and LCD Control Panels are warranted for three (3) years, except for  
the display and touch overlay components that are warranted for a period of one (1) year.  
Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are  
warranted for a period of one (1) year.  
Unless otherwise specified, OEM and custom products are warranted for a period of one  
(1) year.  
AMX Software is warranted for a period of ninety (90) days.  
Batteries and incandescent lamps are not covered under the warranty.  
This warranty extends only to products purchased directly from AMX Corporation or an  
Authorized AMX Dealer. All products returned to AMX require a Return Material Authorization  
(RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA  
number must be clearly marked on the outside of each box. The RMA is valid for a 30-day  
period. After the 30-day period the RMA will be cancelled. Any shipments received not  
consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible  
for products returned without a valid RMA number. AMX Corporation is not liable for any  
damages caused by its products or for the failure of its products to perform. This includes any  
lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is  
not liable for any claim made by a third party or by an AMX Dealer for a third party. This  
limitation of liability applies whether damages are sought, or a claim is made, under this  
warranty or as a tort claim (including negligence and strict product liability), a contract claim, or  
any other claim. This limitation of liability cannot be waived or amended by any person. This  
limitation of liability will be effective even if AMX Corporation or an authorized representative of  
AMX Corporation has been advised of the possibility of any such damages. This limitation of  
liability, however, will not apply to claims for personal injury. Some states do not allow a  
limitation of how long an implied warranty last. Some states do not allow the limitation or  
exclusion of incidental or consequential damages for consumer products. In such states, the  
limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the  
owner specific legal rights. The owner may also have other rights that vary from state to state.  
 
The owner is advised to consult applicable state laws for full determination of rights.  
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES  
NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED  
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX  
CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED  
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED  
TO THE TERMS OF THIS LIMITED WARRANTY.  
93-0000-11 Rev E  
041-004-2606 2/06  
©2006 AMX Corporation.  
All Rights Reserved.  
All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the  
light bulb icon are all trademarks of AMX Corporation.  
AMX reserves the right to alter specifications without notice at any time.  
*In Canada doing business as Panja Inc.  
3000 research drive, richardson, TX 75082 USA  
469.624.8000 • 800.222.0193 • fax 469.624.7153  
technical support 800.932.6993  
 
brussels • dallas • los angeles • mexico city • philadelphia • shanghai • singapore • tampa • toronto* • york  

3Com Network Card DUAXJK10075AAA01 User Manual
4XEM Security Camera IPCAMWPTZ User Manual
AAMP of America Speaker SD20 HD20 User Manual
AAMP of America TV Cables PXDX KI User Manual
ADTRAN Network Card Dual T1 PRI User Manual
Altinex Switch MT104 107 User Manual
Asus Car Video System VG278HR User Manual
ATMT MP3 Player MP150 User Manual
Axor Plumbing Product 0493XX0 User Manual
Behringer Microphone A50 13413 00005 User Manual