Belkin Universal Remote F4F315 T User Manual

P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 1  
F4F315-T  
Us e r Ma nua l  
F4F315-T  
P73240  
 
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 1  
To Test Straight Twisted Pair  
(Shielded or Unshielded) Cables  
1. Plug one end of the cable into the modular jack on the  
master unit and the other end into the modular jack of  
the remote terminator.  
2. As soon as the Power is turned on, the LEDs on the  
remote terminator will start to scan each pair one by one.  
If the cable wiring is intact, the LEDs corresponding to  
each pair will illuminate green. If the LEDs illuminate  
green first and red afterwards or do not illuminate, the  
cable wiring is bad.  
3. Straight-through vs. Crossover: If the LED lights up from  
top to bottom (1&2, 3&6, 4&5, 7&8), the cable is wired in  
a straight-through configuration. If the pairs are crossed,  
the LED will not light up from top to bottom; it will light  
up in a different order depending on how the pairs  
are crossed.  
4. For RJ45 cables that have only 2 pairs (4 conductors)  
wired please refer to the LED guide printed on the  
remote terminator. In those applications only 2 of the  
LEDs will need to illuminate green to indicate a  
good cable.  
5. For shielded cable, you may test the shielding by pushing  
the GND (Ground) button on. The pair LEDs and GND  
LED should all illuminate green except for pair 3 & 6. If  
any LEDs illuminate green first and red afterwards or do  
not illuminate, the shielding is bad.  
Caution:  
1. Do not connect the cable tester to a live circuit.  
2. Make sure the 9-Volt alkaline battery is installed  
properly in the battery compartment.  
1
 
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 2  
To Test Coax Cable (BNC)  
1. Plug one end of cable to the BNC socket of master unit  
and the other end to the BNC terminator included with  
the F4F315-T.  
2. Push the Power button to the ON position on the master  
unit. If the BNC LED illuminates, the cable is bad.  
3. If the cable passes step 2, then push the BNC test button  
on the side of the master unit. The BNC LED will  
illuminate green if the cable is good. If it illuminates red,  
the cable is bad.  
Pair Configurations For Cables  
with Modular Connectors  
2
 
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 3  
Product Detail  
BNC Terminator  
Master Unit  
Remote Terminator  
3
 
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 4  
be lkin.com  
Belkin Components  
501 West Walnut Street  
Compton • CA • 90220 • USA  
Tel: 310.898.1100  
Fax: 310.898.1111  
Belkin Components, Ltd.  
Unit 13 • Gatelodge Close • Round Spinney  
Northampton • Northants • NN3 8RX • UK  
Tel: +44 (0) 1604678300  
Fax: +44 (0) 1604678330  
Belkin Components B.V.  
Diamantlaan 8 • 2132 WV  
Hoofddorp • The Netherlands  
Tel: +31 (0) 235698765  
Fax: +31 (0) 235612694  
©1999 Belkin Components. All Rights Reserved. All Trade Names are  
Registered Trademarks of Respective Manufacturers Listed.  
 
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 5  
 
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 6  
 

Blackberry Cell Phone 103 User Manual
Black Decker Trimmer HH2450 User Manual
Blaupunkt Car Stereo System DAB47 User Manual
Blomberg Refrigerator SND 9682 ED A+ User Manual
Braun Iron PV 2550 User Manual
Cannon Electric Pressure Cooker 10426G User Manual
Canon Camcorder 5253B002 User Manual
Canon Camera Lens 2540A002 User Manual
Casio Electronic Keyboard SK 8 User Manual
Chief Manufacturing Indoor Furnishings KCG220 User Manual