Extron electronic Projector SYSTEM 8 10 PLUS User Manual

Hughes Installation  
Configuration and Connections  
SYSTEM 8/10 Plus  
PROJECTOR COMMUNICATIONS KIT  
ATTENTION!  
PLEASE READ THIS DOCUMENT FOR IMPORTANT  
INSTALLATION INSTRUCTIONS  
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:  
Kit Type: HUGHES  
Included Communications Adapter(s):  
Quantity  
Part Number  
Description  
1
26-467-01  
ADP, UNV, “A”  
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING  
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS  
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS  
INDICATED BY THE “” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL  
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER  
WITH THE CORRECT SETTINGS.  
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND  
SIGNAL CONNECTION INSTRUCTIONS.  
THIS SWITCHER HAS BEEN CONFIGURED FOR: HUGHES/JVC  
Config  
as  
Model  
Rotary Switches Cable  
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter  
SW15 Settings  
Comm  
Hughes-JVC  
Hughes DILA  
0
0
0
0
6
F
5
8
J2 ↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
J2 ↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-412-01 Rev. A  
 
Hughes Installation  
Configuration and Connections  
System 8/10 Plus to Hughes-JVC DILA Projector Connections (RS-232)  
Use the illustration below as a guide when connecting the System 8/10 Plus to  
the Hughes-JVC DILA projector. Refer to projector documentation to continue  
the installation.  
S-Video Adapter  
COMPUTER IN-2  
AUDIO  
AV IN  
Y/C  
VIDEO  
PC  
COMPUTER IN-2  
AUDIO  
AUDIO  
R
L
Y
P
G
B
H/Cs  
R
B /B-Y  
V
P
R /R-Y  
COMPUTER  
OUT  
CONTROL  
REMOTE  
9-Pin Female  
AUDIO OUT  
RS - 232C  
CommAdapter  
26-467-01  
Composite  
Video  
15-Pin  
Male  
S-Video  
RGBHV 5 BNC  
________ When RS-232 control of the projector is used, the projector’s IR remote can be  
used. However, because the projector’s IR remote does not communicate with  
the System 8/10 Plus switcher, the projector and switcher can become out-of-  
sync if the projector’s IR remote is used to change the projector’s input, picture  
mute or power settings. Should this occur, press the power, mute or channel  
buttons on the switcher to allow the projector and switcher to resynchronize.  
________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the  
System 8/10 Plus User’s Manual.  
________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.  
Page 2  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-412-01 Rev. A  
 
Hughes Installation  
Configuration and Connections  
Hughes/JVC Projector Configuration  
Check to see if the System 8/10 PLUS is already configured for the Hughes/JVC  
projector. The general setup is explained on page 3-4 and the switch settings for  
the Hughes/JVC projector are repeated below.  
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS  
front panel. See bottom of page 3-3. The label on the back of the access cover  
also has the configuration information.  
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS  
to verify that the main power is OFF; also turn the projector power OFF.  
2. Set the switches as follows:  
Config  
as  
Model  
Rotary Switches Cable  
RS1 RS2 RS3 RS4 J2/J3 1 2  
SW15 Settings  
Comm  
Adapter  
3
4
5
6
7 8 9 10  
Hughes-JVC  
0
0
6
5
J2  
26-467-01  
4
¯
1
2
3
4
5
6
7
8
9
ON  
10  
_ RS5 is for RGB switching  
delay. See page 3-4 for  
more information on switch  
functions.  
SW15 DIP Switch  
RS2  
RS3  
RS4  
RS5 RS2 RS1  
RS1  
RS3 RS4  
Configured For:  
RS-232  
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next  
to “Hughes/JVC”.  
4. Locate the switcher’s Address DIP switches on the rear panel, lower right.  
Unless this is part of a master/slave system, set #3 and #5 to the up position and  
the others down. See picture to the left.  
Use the illustration on the facing page to do the following steps.  
5. Connect the Comm Adapter’s 9-pin female connector to the 9-pin male “Control  
Out” connector on the rear panel of the projector.  
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the  
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear  
panel of the System 8/10 PLUS.  
______ Secure the screws on all D connectors.  
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the  
Hughes/JVC projector inputs according to the application requirements. (RGBS,  
S-Video and/or Composite Video)  
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The  
Main Power LED should light. Apply power to the projector.  
9. Return System 8/10 PLUS and projector to normal operation.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-412-01 Rev. A  
Page 3  
 
Hughes Installation  
Configuration and Connections  
Hughes/JVC 300/400 Series Projector Connections  
Use the illustration below when connecting the System 8/10 PLUS to a Hughes/  
JVC 300/400 Series projector. Refer to Hughes/JVC documentation to continue  
the installation.  
________ If the installation includes looping (master/slave) switchers, see Chapter 5.  
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-412-01 Rev. A  
Page 4  
 
Hughes Installation  
Configuration and Connections  
Hughes / JVC Model HJT 100/200 Series Connection Diagram  
Use the illustration below as a guide when connecting the System 8/10 PLUS to a  
Hughes/JVC HJT 100/200 projector. Refer to Hughes documentation to continue  
the installation.  
Hughes HJT 200 Projector  
Terminal In  
Port A  
Control Out  
(Port B)  
CC 50'  
________ If the installation includes looping (master/slave) switchers, see Chapter 5.  
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-412-01 Rev. A  
Page 5  
 
Hughes Installation  
Configuration and Connections  
Special Instructions for the HJT Model 100/200 Series  
The projector documentation provides instructions on how to set up and  
configure the Model 100/200 Series Projector for proper operation with the  
System 8/10 PLUS.  
The baud rate for the Extron switchers is 19200. Since Port A is locked to a  
baud rate of 9600, Port B should be used for Extron Switchers. The projector  
port assignment must be selected and the VIC channel assignment must be  
edited for a switcher. Following is a description of the HJT 100/200 Series Menu.  
To select the Baud Rate from the Projector:  
1. Go to Main Menu, select #7, System, then #4, Comm. Setup.  
2. From the Comm. Setup menu, select Port B Speed.  
3. From the Speed selection list, select 19200.  
4. Press Escape to go back to the Comm. Setup level.  
To set the projector port assignment from the Projector:  
1. From the Comm. Setup menu, select Port B Device.  
2. From the Device type list, select #3, Video Switcher.  
3. Turn power off at the remote control.  
4. Wait until the Arc Lamp fans have stopped running and provide a system cold  
boot by toggling the circuit breaker on the projector rear panel to Off, then back  
to On.  
To edit the VIC channel assignment from the Projector:  
(see the Model 100/200 User’s Guide, Section 5.3.1 for more information on  
editing):  
1. From the Channels list, select the channel that the switcher will be assigned  
to.  
2. Press Mode. This is a toggle key that brings up a submenu for editing. (Press  
Mode again to remove the submenu.)  
3. Select Edit from the submenu and press Enter.  
4. Use the right arrow key to toggle over to the third VIC column.  
5. Press Enter and use the up/down arrow keys to select the current switcher  
channel number. Press Enter when the current switcher channel number is  
shown.  
6. Press Escape to exit the Edit mode.  
Extron • System 8/10 PLUS • User’s Manual • P/N 68-412-01 Rev. A  
Page 6  
 

Extron electronic Home Theater Server 68 1921 50 User Manual
Fellowes Binding Machine Pulsar 300 User Manual
Fender Speaker 1110X User Manual
Frigidaire Washer 134305500A User Manual
Fujitsu Printer FTP 608 Series User Manual
GE Clothes Dryer PSXH43 User Manual
GE Food Warmer JKD915 User Manual
Generac Pressure Washer 1537 0 User Manual
GE Oven JKP17 User Manual
GE Water System GNSF18Z01 User Manual